Suntan Blog

Suntan Technology Company Limited
---All Kinds of Capacitors

Suntan Technology Company Limited
---All Kinds of Capacitors

Good news to share with all of Suntan customers, we have updated our Ceramic Trimmer Capacitors product catalog.

Suntan is a manufacturer based in Hong Kong specializing in the production of ceramic trimmer capacitor, including 3mm-SMD Ceramic Trimmer Capacitor, 3mm-Special SMD Ceramic Trimmer Capacitor, 5mm Trimmer Ceramic Capacitor, 6mm Ceramic Trimmer Capacitor etc.

Please click on the following link for more information
http://www.suntan.com.hk/Ceramic-Trimmer-Capacitors/
http://www.suntan.com.hk/pdf/catalogs/Suntan-Ceramic-Trimmer-Capacitors.pdf

Suntan Technology Company Limited
----All Kinds of Capacitors

Suntan is now a leading firm in the electronic component industry. Based on our unique design and processing technologies we offer a variety of ceramic products including 3mm ceramic trimmer capacitors, 5mm Trimmer Ceramic Capacitor, 6mm and 7mm Ceramic Trimmer Capacitor etc.

The following is one of our Ceramic Trimmer Capacitors,please see its features.If you are interested in other types of Ceramic Trimmer Capacitor,please visit www.suntan.com.hk for your reference.

5mm Ceramic Trimmer Capacitor Features:

● As well as applications to small sized electronic apparatus, this series is designed for easy handing and is available with a variety of adjustment method (top, buttom, side and double sides);
● Wide mounting sizes and variable adjustment available;
● Lots of capacity ranges,3pF through 90pF;
● Sturdy mechanical structure against vibration or shock.

(1) Ensure that PCB hole spacing complies the terminal spacing requirement of the intended Trimmer Capacitor model. Incorrect hole spacing may lower Trimmer Capacitor performance due to excessive stress applied the terminal.

(2) Mount Trimmer Capacitor in contact with PCB.

(3) Do not apply bending stress after the Trimmer Capacitor has been mounted to the PCB.

(4) Note Trimmer Capacitor polarity to minimize the influence of stray Capacitance . Refer to the outlines of each model.

(5) Do not warp and /or bend PC board to prevent Trimmer Capacitor from breakage.

When measured at room temperature (25°C ± 5°C) and at a frequency of 0.1 to 1 Megahertz, the minimum capacitance shall not be greater than that specified at minimum setting  with a +10% tolerance and the maximum capacitance shall not be less than that specified maximum setting with a - 10% tolerance.

The capacitance drift shall be determined as the greatest difference between any two of the three 25°C measurements obtained during the temperature characteristic test.  The capacitance drift shall not exceed 0.75% or 0.5pF, whichever is greater.

Torque

The torque test should be done by rotating the rotor through one full turn within 15~100gf.cm. Please noted that it might cause the torque will decrease against the rotation increase

Vibration

The maximum capacitance was set at 80 to 90% , however it shall be subjected to vibration test at 1.5mm amplitude, with frequency range from 10 to 55 Hz ,and  then return to 10 Hz for 1 minute applied for 2 hours in each of three mutually perpendicular planes. (total 6 hours) The capacitor shall be rigidly mounted by their normal mounting means .The vibration capacitance shall be within  ±0.25pF or ±2% ( whichever is greater ).

Mounting

(1) Do not apply excessive force (preferably 5.0 N max.), when the trimmer capacitor  is mounted on the PCB.
(2) Do not warp and/or bend PCB to prevent trimmer capacitor from breaking.
(3) Use the suitable dimension of the pick-up nozzle (1.1-1.2mm external diameter and 0.8-0.9mm bore diameter).

Cleaning

Cannot be cleaned because of open construction.

Other

Note the polarity of the trimmer capacitor to minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)

The capacitor at approximately 75% of the guaranteed maximum capacitance, shall be tested for 250 hours at twice rated voltage, and at a temperature equal to the maximum operating temperature± 3°C for the respective style. At the end of this period the capacitance shall not have changed more than ±5% or ±0.5pF, whichever is greater, from its value before the life test. The I.R. shall be 1 gigaohm minimum and the“Q” at 1 MHz shall be a minimum of 40% of the initial test limit.